Difficulty
Moderate
Steps
14
Time Required
Suggest a time??
Sections
4
- Power Button Panel
- 4 steps
- Keyboard
- 3 steps
- Touchpad Panel
- 4 steps
- Wi-Fi Card
- 3 steps
Flags
0
BackHP ProBook 4320t
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery Removal
- Flip the laptop upside down and remove battery by pressing inward on the two latches holding the battery in.
Flip the laptop upside down and remove battery by pressing inward on the two latches holding the battery in.
1024
Step 2
Screws
- Unscrew the four (2.5 mm Phillips) screws (Use Phillips #0 Screwdriver).
Unscrew the four (2.5 mm Phillips) screws (Use Phillips #0 Screwdriver).
Step 3
Flip
- Flip laptop over and open it.
Flip laptop over and open it.
Step 4
Push N Lift
- Slightly push up while lifting up on the power button panel to release the panel.
Slightly push up while lifting up on the power button panel to release the panel.
Step 5
Unscrewing
- Unscrew the four (2.5 mm Phillips) screws holding the keyboard in (Use Phillips #0 Screwdriver).
Unscrew the four (2.5 mm Phillips) screws holding the keyboard in (Use Phillips #0 Screwdriver).
Step 6
Careful Now
- Carefully (holding both sides of the keyboard), push up and lift slightly.
- Keyboard is still connected via a ribbon cable.
- Move the keyboard slightly to the left to have access to the keyboard ribbon cable.
Carefully (holding both sides of the keyboard), push up and lift slightly.
Keyboard is still connected via a ribbon cable.
Move the keyboard slightly to the left to have access to the keyboard ribbon cable.
Step 7
Disconnect Wire
- Use the black spudger to lift the black latch holding the keyboard ribbon cable.
Use the black spudger to lift the black latch holding the keyboard ribbon cable.
Step 8
Unscrew
- Unscrew the three (2.5 mm Phillips) screws holding the bottom touchpad panel.
Unscrew the three (2.5 mm Phillips) screws holding the bottom touchpad panel.
Step 9
Slide the Panel Off
- Carefully slide the bottom panel to the right.
- Keyboard is connected via a wire to the back of the panel.
Carefully slide the bottom panel to the right.
Keyboard is connected via a wire to the back of the panel.
Step 10
Lift up Carefully
- Flip the bottom touchpad panel directly towards the screen, being sure to not lift it too high.
- Keep an eye on the ZIF connector underneath, make sure it is not pulled accidentally.
Flip the bottom touchpad panel directly towards the screen, being sure to not lift it too high.
Keep an eye on the ZIF connector underneath, make sure it is not pulled accidentally.
Step 11
Disconnect Wire
- Using the black spudger, slightly pry up on the ZIF connector and lift out the wire carefully.
Using the black spudger, slightly pry up on the ZIF connector and lift out the wire carefully.
Step 12
Wi-Fi Card
- Use black spudger to detach the two antenna cable connectors to the Wi-Fi card.
- Be careful not to break the cords.
Use black spudger to detach the two antenna cable connectors to the Wi-Fi card.
Be careful not to break the cords.
Step 13
- Unscrew the two (2.5 mm Phillips) screws holding the wifi card in.
- Be careful because upon the last turn of the screw, the Wi-Fi card lifts up slightly.
Unscrew the two (2.5 mm Phillips) screws holding the wifi card in.
Be careful because upon the last turn of the screw, the Wi-Fi card lifts up slightly.
Step 14
- Pull the Wi-Fi card towards the left to remove.
Pull the Wi-Fi card towards the left to remove.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Joshua
Member since: 09/23/2014
134 Reputation
6 Guides authored
Badges:
11
+8 more badges
Team
USF Tampa, Team 9-5, Blackwell Fall 2014
Member of USF Tampa, Team 9-5, Blackwell Fall 2014
USFT-BLACKWELL-F14S9G5
4 Members
10 Guides authored
