Difficulty

Moderate

Steps

12

Time Required

                          25 minutes

Sections

3

  • Power Button Panel
  • 4 steps
  • Keyboard
  • 3 steps
  • Speakers
  • 5 steps

Flags

0

  • BackHP ProBook 4320t

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery Removal
  • Flip the laptop upside down and remove battery by pressing inward on the two latches holding the battery in.

Flip the laptop upside down and remove battery by pressing inward on the two latches holding the battery in.

1024

Step 2

              Screws
  • Unscrew the four (2.5 mm Phillips) screws (Use Phillips #0 Screwdriver).

Unscrew the four (2.5 mm Phillips) screws (Use Phillips #0 Screwdriver).

Step 3

              Flip
  • Flip laptop over and open it.

Flip laptop over and open it.

Step 4

              Push N Lift
  • Slightly push up while lifting up on the power button panel to release the panel.

Slightly push up while lifting up on the power button panel to release the panel.

Step 5

              Unscrewing
  • Unscrew the four (2.5 mm Phillips) screws holding the keyboard in (Use Phillips #0 Screwdriver).

Unscrew the four (2.5 mm Phillips) screws holding the keyboard in (Use Phillips #0 Screwdriver).

Step 6

              Careful Now
  • Carefully (holding both sides of the keyboard), push up and lift slightly.
  • Keyboard is still connected via a ribbon cable.
  • Move the keyboard slightly to the left to have access to the keyboard ribbon cable.

Carefully (holding both sides of the keyboard), push up and lift slightly.

Keyboard is still connected via a ribbon cable.

Move the keyboard slightly to the left to have access to the keyboard ribbon cable.

Step 7

              Disconnect Wire
  • Use the black spudger to lift the black latch holding the keyboard ribbon cable.

Use the black spudger to lift the black latch holding the keyboard ribbon cable.

Step 8

              Speakers
  • Use the black spudger tool to lift the white, black, and red ribbon cable connector up so that it is disconnected.

Use the black spudger tool to lift the white, black, and red ribbon cable connector up so that it is disconnected.

Step 9

  • Unscrew the two (2.5 mm Phillips) screws (located on the upper most part of the computer) holding the speakers in.

Unscrew the two (2.5 mm Phillips) screws (located on the upper most part of the computer) holding the speakers in.

Step 10

  • Using the black spudger tool, gently pry off the right speaker.
  • Be careful to not break the cord.

Using the black spudger tool, gently pry off the right speaker.

Be careful to not break the cord.

Step 11

  • Remove the cords from the retention clips.

Remove the cords from the retention clips.

Step 12

  • Remove the left speaker as completed in step #10.

Remove the left speaker as completed in step #10.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors 


                    Eric Markham

Member since: 08/29/2014

227 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team 9-5, Blackwell Fall 2014                        

                                                  Member of USF Tampa, Team 9-5, Blackwell Fall 2014 



                    USFT-BLACKWELL-F14S9G5                     


                                            4 Members                     


                                            10 Guides authored