Hp Photosmart Premium C309G Touchsmart Display Screen Replacement Repair Guide

Difficulty

Easy

Steps

13

Time Required

                          15 - 20 minutes            

Sections

1

• TouchSmart Display Screen
• 13 steps

Flags

0

• BackHP Photosmart Premium C309g

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              TouchSmart Display Screen               

• Open the top of printer. The printer should appear as shown.

Open the top of printer. The printer should appear as shown.

1024

Step 2

• Use the blue plastic opening tool to pry the trim pieces all the way around the printer.
• Loosen the pieces around the edges before pulling to remove from the printer.
• Pull the (4) trim pieces off and set them aside.

Use the blue plastic opening tool to pry the trim pieces all the way around the printer.

Loosen the pieces around the edges before pulling to remove from the printer.

Pull the (4) trim pieces off and set them aside.

Step 3

• Using the blue plastic opening tool, pull from the middle and then slide back to remove the side panels.
• The side trim pieces need to be removed before the front trim pieces.

Using the blue plastic opening tool, pull from the middle and then slide back to remove the side panels.

The side trim pieces need to be removed before the front trim pieces.

Step 4

• Using the T9 Torx Security screwdriver bit, unscrew the five 12mm screws shown.

Using the T9 Torx Security screwdriver bit, unscrew the five 12mm screws shown.

Step 5

• The scanner flap is attached by a clip that can be dislodged by pulling it gently away from the printer.
• Keeping the scanner flap upright, slide it toward the unattached clip in order to dislodge the second clip.
• Both clips will come unattached and you can set the scanner flap aside.

The scanner flap is attached by a clip that can be dislodged by pulling it gently away from the printer.

Keeping the scanner flap upright, slide it toward the unattached clip in order to dislodge the second clip.

Both clips will come unattached and you can set the scanner flap aside.

Step 6

• Lift the scanner glass piece from the printer and set it aside.

Lift the scanner glass piece from the printer and set it aside.

Step 7

• Gently pull the display screen away from the printer.
• Locate & unscrew the two 12mm screws using the T9 Torx Security screwdriver bit.

Gently pull the display screen away from the printer.

Locate & unscrew the two 12mm screws using the T9 Torx Security screwdriver bit.

Step 8

• Place thumb and forefinger where shown and pull this piece away from the printer.
• Do not pull it away too hard. The piece is still connected by wiring ribbon.

Place thumb and forefinger where shown and pull this piece away from the printer.

Do not pull it away too hard. The piece is still connected by wiring ribbon.

Step 9

• Pull both wiring ribbons out from the display screen piece. This will separate the piece from the printer.
• Use tweezers if necessary.

Pull both wiring ribbons out from the display screen piece. This will separate the piece from the printer.

Use tweezers if necessary.

Step 10

• Push forward and down to release the retaining piece. This will detach the display screen from the front panel.

Push forward and down to release the retaining piece. This will detach the display screen from the front panel.

Step 11

• Set the display screen face down.
• Locate and unscrew all four 12mm screws on the back on the display screen using the T9 Torx Security screwdriver bit.

Set the display screen face down.

Locate and unscrew all four 12mm screws on the back on the display screen using the T9 Torx Security screwdriver bit.

Step 12

• Lift the back of the display screen to remove it.

Lift the back of the display screen to remove it.

Step 13

• Place hands as shown and push with your thumbs to detach the plastic from the screen.

Place hands as shown and push with your thumbs to detach the plastic from the screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 2 other contributors 

                    Laura                     

Member since: 10/23/2014

661 Reputation

                                      3 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges                           

Team

                       Michigan Tech, Team 1-2, Lauer Fall 2014                        

                                                  Member of Michigan Tech, Team 1-2, Lauer Fall 2014 



                    MTU-LAUER-F14S1G2                     


                                            3 Members                     


                                            5 Guides authored                     

fernando - May 13, 2016

Reply

where can i get replacement part