Hp Photosmart D110A Printer Hood Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

7

Time Required

Suggest a time??

Sections

1

• Printer Hood Assembly
• 7 steps

Flags

2

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Step Trimmer

This guide has unnecessary steps. Trim them to be more concise!

• BackHP Photosmart D110a

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

Removing the hood involves removing 4 screws(one of which is placed such that it is difficult to access), and removing some ribbon cables.

Required Tools

• T-9 Screwdriver (T-9 may not work)Needle-Nose Pliers

What you need

Step 1

              Printer Hood Assembly               

• First, begin by removing the printer’s hood.
• Open the printer’s mouth by simply pulling down on it; there are 2 mouth pieces that need to be pulled down.
• Adjust the flap covering the scanner upward, as shown.

First, begin by removing the printer’s hood.

Open the printer’s mouth by simply pulling down on it; there are 2 mouth pieces that need to be pulled down.

Adjust the flap covering the scanner upward, as shown.

1024

Step 2

• Remove the flap for the scanner. The flap is attached with two clips that can be dislodged by pulling lightly away from the printer.

Remove the flap for the scanner. The flap is attached with two clips that can be dislodged by pulling lightly away from the printer.

Step 3

• Locate the three screws on top of the printer.
• The orange circle shows a fourth screw located behind the power panel. Directions to remove this screw are in a later step.

Locate the three screws on top of the printer.

The orange circle shows a fourth screw located behind the power panel. Directions to remove this screw are in a later step.

Step 4

• Remove the three screws from the top of the printer with a T-9 screwdriver as shown.

Remove the three screws from the top of the printer with a T-9 screwdriver as shown.

Step 5

• To access and remove the fourth and final screw attaching the hood, the panel for the power button must be removed as follows:
• Reach into the mouth of the printer and press on the small clip behind the power button. This allows the panel of the power button to be removed.
• A picture of the power button panel removed is provided to show the location of the clip that needs to be pressed.
• After pressing the clip, pull out the power button panel by pulling from right to left.

To access and remove the fourth and final screw attaching the hood, the panel for the power button must be removed as follows:

Reach into the mouth of the printer and press on the small clip behind the power button. This allows the panel of the power button to be removed.

A picture of the power button panel removed is provided to show the location of the clip that needs to be pressed.

After pressing the clip, pull out the power button panel by pulling from right to left.

Step 6

• Remove the exposed screw that was covered by the power button panel.
• Do not try and torque the screw from an angle. This will ruin the screw’s head, and make it even more difficult to remove the screw. Only remove it as already described.
• This screw is placed awkwardly. We found holding a T9 bit in a pair of needle nose pliers gave us enough leverage to pull it up.

Remove the exposed screw that was covered by the power button panel.

Do not try and torque the screw from an angle. This will ruin the screw’s head, and make it even more difficult to remove the screw. Only remove it as already described.

This screw is placed awkwardly. We found holding a T9 bit in a pair of needle nose pliers gave us enough leverage to pull it up.

Step 7

• This step is easier with two people. Carefully have one person lift the hood of the printer 2-3 inches above where it was resting.
• Remove the ribbon cables and wires attaching the motherboard (the only green PCB board) to the hood by gently pulling upward on them.
• When all three cables are removed, lift the hood away from the printer and set it aside.

This step is easier with two people. Carefully have one person lift the hood of the printer 2-3 inches above where it was resting.

Remove the ribbon cables and wires attaching the motherboard (the only green PCB board) to the hood by gently pulling upward on them.

When all three cables are removed, lift the hood away from the printer and set it aside.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 12 other contributors 

                    Alessandro Andreatta                     

Member since: 04/01/2011

111 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges                           

Team

                       Cal Poly, Team 10-38, Forte Spring 2011                        

                                                  Member of Cal Poly, Team 10-38, Forte Spring 2011 



                    CPSU-FORTE-S11S10G38                     


                                            5 Members                     


                                            10 Guides authored