Featured
Featured Guide
Difficulty
Moderate
Steps
17
Time Required
20 - 30 minutes
Sections
3
- Batteries
- 4 steps
- Plastic Casing
- 6 steps
- LCD Screen
- 7 steps
Flags
2
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackHP Photosmart 935
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Batteries
- Flip the camera over so the bottom of the camera is facing you.
Flip the camera over so the bottom of the camera is facing you.
1024
Step 2
- Turn the mode dial to the OFF position.
Turn the mode dial to the OFF position.
Step 3
- Slide the bottom cover in the direction of the arrow to open it.
Slide the bottom cover in the direction of the arrow to open it.
Step 4
- Pull out the batteries.
Pull out the batteries.
Step 5
Plastic Casing
- Use a Phillips #00 screwdriver to remove the two 4.7 mm screws in the bottom of the plastic casing.
Use a Phillips #00 screwdriver to remove the two 4.7 mm screws in the bottom of the plastic casing.
Step 6
- Remove the four 4.7 mm screws on the left side of the camera.
Remove the four 4.7 mm screws on the left side of the camera.
Step 7
- Remove the four 4.7 mm screws on the opposite side of the camera.
Remove the four 4.7 mm screws on the opposite side of the camera.
Step 8
- Use your thumbs to pry the case apart.
- It is easiest to pry the case apart if you start at the bottom.
- The case should come apart with minimal effort. If it doesn’t, you can use a spudger or plastic opening tool to pry it open.
Use your thumbs to pry the case apart.
It is easiest to pry the case apart if you start at the bottom.
The case should come apart with minimal effort. If it doesn’t, you can use a spudger or plastic opening tool to pry it open.
Step 9
- This step requires a significant amount of force.
- Pull the bottom half of the inner camera out of the case by half an inch. This may be difficult.
This step requires a significant amount of force.
Pull the bottom half of the inner camera out of the case by half an inch. This may be difficult.
Step 10
- While pulling the camera out of the case, note the small soft plastic cover on the side. This cover will detach from the rest of the device.
- Once the bottom of the inner camera is pulled out, pull the device out completely.
- Use a firm grasp when removing the device from the case for stability and control.
While pulling the camera out of the case, note the small soft plastic cover on the side. This cover will detach from the rest of the device.
Once the bottom of the inner camera is pulled out, pull the device out completely.
Use a firm grasp when removing the device from the case for stability and control.
Step 11
LCD Screen
- Orient the camera so that the LCD screen is facing you.
- If case is still on, remove it by following the Plastic Casing Installation Guide found in the previous steps.
- Removing the casing completely is crucial to completing this guide.
Orient the camera so that the LCD screen is facing you.
If case is still on, remove it by following the Plastic Casing Installation Guide found in the previous steps.
Removing the casing completely is crucial to completing this guide.
Step 12
- Using a Phillips #00 remove the four 4.40 mm screws that secure the LCD screen to the frame.
Using a Phillips #00 remove the four 4.40 mm screws that secure the LCD screen to the frame.
Step 13
- Allow the LCD screen to flip down. This will expose the electric strip that connects the screen to the camera.
Allow the LCD screen to flip down. This will expose the electric strip that connects the screen to the camera.
Step 14
- Look for where the yellow electric strip is attached to the camera. You will find a plastic grey bar and a white base holding this strip in place.
- Push the grey bar away from the white base. This will release the yellow electric strip and free the LCD screen from the camera.
Look for where the yellow electric strip is attached to the camera. You will find a plastic grey bar and a white base holding this strip in place.
Push the grey bar away from the white base. This will release the yellow electric strip and free the LCD screen from the camera.
Step 15
- Unplug the connected red and white wires. They will come out with the small white casing.
Unplug the connected red and white wires. They will come out with the small white casing.
Step 16
- Flip camera so that the lens is facing away from you. You should be looking at the LCD screen.
Flip camera so that the lens is facing away from you. You should be looking at the LCD screen.
Step 17
- Remove the bottom left LCD mounting frame screw. The screen should come loose after the screw is removed.
- Remove the LCD screen from the camera. Make sure that the electric strip comes out with screen.
Remove the bottom left LCD mounting frame screw. The screen should come loose after the screw is removed.
Remove the LCD screen from the camera. Make sure that the electric strip comes out with screen.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 10 other contributors
Nick Oleskowicz
Member since: 04/03/2012
275 Reputation
3 Guides authored
Badges:
9
+6 more badges
Team
Cal Poly, Team 15-13, Forte Spring 2012
Member of Cal Poly, Team 15-13, Forte Spring 2012
CPSU-FORTE-S12S15G13
5 Members
10 Guides authored
Saverio Mercurio - Sep 28, 2021
Reply
Thank for this very good job, I own this this camera so it is will be quite easy to fix it following your guide.
