Hp Pavilion Zv5000 Speaker Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 - 2 hours

Sections

Battery
3 steps
Hard Drive
2 steps
Keyboard
8 steps
Screen
7 steps
Speaker
9 steps

Flags

Incorrect Tools

Help make this guide better by using the correct tools in images and/or text.

BackHP Pavilion zv5000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Make sure that your device is properly shut down and unplugged from any outlet.
Flip Pavilion over so that the bottom faces up and locate the battery in the bottom left corner.

Make sure that your device is properly shut down and unplugged from any outlet.

Flip Pavilion over so that the bottom faces up and locate the battery in the bottom left corner.

1024

Step 2

Press and slide up the battery release tab with your thumb until the battery pops out of place.

Press and slide up the battery release tab with your thumb until the battery pops out of place.

Step 3

Using two fingers, pry the rest of the battery out of the socket.

Using two fingers, pry the rest of the battery out of the socket.

Step 4

              Hard Drive

Make sure that the Pavilion is completely powered down and unplugged. Failure to do so may result in an electrical shock.
Using the Phillips #0 screwdriver, unscrew the two Phillips PM 2.5X6.0mm screws.
The two screws do not come out of the hard drive assembly, they simply disconnect the assembly from the laptop.

Make sure that the Pavilion is completely powered down and unplugged. Failure to do so may result in an electrical shock.

Using the Phillips #0 screwdriver, unscrew the two Phillips PM 2.5X6.0mm screws.

The two screws do not come out of the hard drive assembly, they simply disconnect the assembly from the laptop.

Step 5

Place the spudger underneath the cover of the hard drive and push up gently until the hard drive pops out of place.
Completely remove the hard drive from its socket.
If the plastic spudger is not sturdy enough to pop the hard drive out of place, try carefully using the metal spudger.

Place the spudger underneath the cover of the hard drive and push up gently until the hard drive pops out of place.

Completely remove the hard drive from its socket.

If the plastic spudger is not sturdy enough to pop the hard drive out of place, try carefully using the metal spudger.

Step 6

              Keyboard

Using a Phillips #0 screwdriver, unscrew all four Phillips PM 2.5X13.0mm screws and place in a secure area until the end of the project.

Using a Phillips #0 screwdriver, unscrew all four Phillips PM 2.5X13.0mm screws and place in a secure area until the end of the project.

Step 7

Flip laptop back over and open as far as it can go.

Flip laptop back over and open as far as it can go.

Step 8

Use the flat edge of the plastic spudger inserted under the bottom of the strip cover and pry upwards to un-clip the cover, starting at the right and moving to the left.
If the plastic spudger is not doing the trick, try using the metal spudger careful to not pop any keys out.

Use the flat edge of the plastic spudger inserted under the bottom of the strip cover and pry upwards to un-clip the cover, starting at the right and moving to the left.

If the plastic spudger is not doing the trick, try using the metal spudger careful to not pop any keys out.

Step 9

Use hands to completely lift off the strip cover and remove.

Use hands to completely lift off the strip cover and remove.

Step 10

Use the Phillips #0 screwdriver again, unscrew all four Phillips PM 2.5X13.0mm screws from the top of the keyboard and set aside.

Use the Phillips #0 screwdriver again, unscrew all four Phillips PM 2.5X13.0mm screws from the top of the keyboard and set aside.

Step 11

Using your hands, lift the keyboard up from the top towards yourself until the keyboard is resting in your hand.
Do not aggressively pull at the keyboard for risk of ripping the connector cable.

Using your hands, lift the keyboard up from the top towards yourself until the keyboard is resting in your hand.

Do not aggressively pull at the keyboard for risk of ripping the connector cable.

Step 12

Gently slide out the connecting cable from the laptop to the keyboard.
Do not aggressively pull at the connecting cable.

Gently slide out the connecting cable from the laptop to the keyboard.

Do not aggressively pull at the connecting cable.

Step 13

Completely remove the keyboard from the rest of the laptop.

Completely remove the keyboard from the rest of the laptop.

Step 14

              Screen

Flip the Pavilion back over on its backside.

Flip the Pavilion back over on its backside.

Step 15

Using the same Phillips #0 screwdriver, unscrew the six Phillips PM 2.5X6.0mm screws.
Also remove the four Phillips PM 2.5X13.0mm screws to remove the thermal plate with the same screwdriver.

Using the same Phillips #0 screwdriver, unscrew the six Phillips PM 2.5X6.0mm screws.

Also remove the four Phillips PM 2.5X13.0mm screws to remove the thermal plate with the same screwdriver.

Step 16

Flip the laptop back over and open the lid all the way.
Using the flat edge of the plastic spudger, pry straight up to remove the Mini PCI Connector Cables from the board.
Tweezers can also be used to gently squeeze and pull up on the Mini PCI Cable Connectors to remove from the board.
When reinstalling, place the Mini PCI Connector Cables back in place and gently press straight down until they snap into place.

Flip the laptop back over and open the lid all the way.

Using the flat edge of the plastic spudger, pry straight up to remove the Mini PCI Connector Cables from the board.

Tweezers can also be used to gently squeeze and pull up on the Mini PCI Cable Connectors to remove from the board.

When reinstalling, place the Mini PCI Connector Cables back in place and gently press straight down until they snap into place.

Step 17

Using the tweezers, gently squeeze and pull backwards on the display cable until it is disconnected.
To reinsert, simply align the display cable to its proper spot and gently push into place.

Using the tweezers, gently squeeze and pull backwards on the display cable until it is disconnected.

To reinsert, simply align the display cable to its proper spot and gently push into place.

Step 18

Use the Phillips #0 screwdriver again to remove the four Phillips 2.5X13.0mm screws that hold the clips for the screen into place.

Use the Phillips #0 screwdriver again to remove the four Phillips 2.5X13.0mm screws that hold the clips for the screen into place.

Step 19

Turn the laptop around until the top cover is facing you. Keep the laptop in an open position.
Unscrew the four Phillips PM 2.5X6.0mm screws using the Phillips #0 that hold the clips of the screen on to the base.

Turn the laptop around until the top cover is facing you. Keep the laptop in an open position.

Unscrew the four Phillips PM 2.5X6.0mm screws using the Phillips #0 that hold the clips of the screen on to the base.

Step 20

Firmly grasp the top of the screen with your hands and pull towards you and upwards to remove the screen from the base.

Firmly grasp the top of the screen with your hands and pull towards you and upwards to remove the screen from the base.

Step 21

              Speaker

Flip the back laptop over so the bottom of the laptop is facing up.

Flip the back laptop over so the bottom of the laptop is facing up.

Step 22

Unscrew the two Phillip PM 2.5X6.0mm screws in the top right that hold the optical cover in place using a Philips #0 screwdriver.

Unscrew the two Phillip PM 2.5X6.0mm screws in the top right that hold the optical cover in place using a Philips #0 screwdriver.

Step 23

Use the plastic spudger and insert it into the side of the CD drive and push outwards to pop the drive out of place.
If the plastic spudger does not pop the CD drive out, try carefully using the metal spudger.

Use the plastic spudger and insert it into the side of the CD drive and push outwards to pop the drive out of place.

If the plastic spudger does not pop the CD drive out, try carefully using the metal spudger.

Step 24

Using your hands, firmly grasp the CD drive and pull outwards until it is completely removed.

Using your hands, firmly grasp the CD drive and pull outwards until it is completely removed.

Step 25

After the CD Drive is removed, return to the back plate of the laptop.
There are four Philip PM 2.5X6.0mm small screws.
There are ten Phillip PM 2.5X13.0mm long screws.
Using the same Philip’s #0 screwdriver, remove all fourteen screws.

After the CD Drive is removed, return to the back plate of the laptop.

There are four Philip PM 2.5X6.0mm small screws.

There are ten Phillip PM 2.5X13.0mm long screws.

Using the same Philip’s #0 screwdriver, remove all fourteen screws.

Step 26

Insert the plastic spudger into the edge of the base plate and the side of the laptop directly above the battery space and gently pry the base plate loose from its clips moving from right to left.
Once the clips are undone, lift the base plate up and off of the laptop.
If the plastic spudger is not sturdy enough to pop the clips out of place, carefully use the metal spudger.

Insert the plastic spudger into the edge of the base plate and the side of the laptop directly above the battery space and gently pry the base plate loose from its clips moving from right to left.

Once the clips are undone, lift the base plate up and off of the laptop.

If the plastic spudger is not sturdy enough to pop the clips out of place, carefully use the metal spudger.

Step 27

Unscrew the one Phillip 2.5X6.0mm screw using the #0 Phillips again holding the speaker into place but do not remove speaker

Unscrew the one Phillip 2.5X6.0mm screw using the #0 Phillips again holding the speaker into place but do not remove speaker

Step 28

Using your fingers, firmly grasp the wires that connect the speaker to the board and gently pull the cable away from the connector in the same direction that the wires are running.
Apply even pulling force to all the wires so that no one wire is overly strained.

Using your fingers, firmly grasp the wires that connect the speaker to the board and gently pull the cable away from the connector in the same direction that the wires are running.

Apply even pulling force to all the wires so that no one wire is overly strained.

Step 29

Grasp speaker assembly firmly and pull towards you and up to remove the speaker completely from the laptop.

Grasp speaker assembly firmly and pull towards you and up to remove the speaker completely from the laptop.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Eliza Marks

Member since: 10/18/2016

649 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       UMass Dartmouth, Team 4-6, Catania Fall 2016                        

                                                  Member of UMass Dartmouth, Team 4-6, Catania Fall 2016 



                    UMASSD-CATANIA-F16S4G6                     


                                            3 Members                     


                                            5 Guides authored

Incorrect Tools#

Introduction#

What you need#

Team#

Incorrect Tools

Introduction

What you need

Team