Hp Pavilion Zv5000 Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          45 minutes - 1 hour

Sections

Battery
3 steps
Keyboard
8 steps
Screen
7 steps

Flags

BackHP Pavilion zv5000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Make sure that your device is properly shut down and unplugged from any outlet.
Flip Pavilion over so that the bottom faces up and locate the battery in the bottom left corner.

Make sure that your device is properly shut down and unplugged from any outlet.

Flip Pavilion over so that the bottom faces up and locate the battery in the bottom left corner.

1024

Step 2

Press and slide up the battery release tab with your thumb until the battery pops out of place.

Press and slide up the battery release tab with your thumb until the battery pops out of place.

Step 3

Using two fingers, pry the rest of the battery out of the socket.

Using two fingers, pry the rest of the battery out of the socket.

Step 4

              Keyboard

Using a Phillips #0 screwdriver, unscrew all four Phillips PM 2.5X13.0mm screws and place in a secure area until the end of the project.

Using a Phillips #0 screwdriver, unscrew all four Phillips PM 2.5X13.0mm screws and place in a secure area until the end of the project.

Step 5

Flip laptop back over and open as far as it can go.

Flip laptop back over and open as far as it can go.

Step 6

Use the flat edge of the plastic spudger inserted under the bottom of the strip cover and pry upwards to un-clip the cover, starting at the right and moving to the left.
If the plastic spudger is not doing the trick, try using the metal spudger careful to not pop any keys out.

Use the flat edge of the plastic spudger inserted under the bottom of the strip cover and pry upwards to un-clip the cover, starting at the right and moving to the left.

If the plastic spudger is not doing the trick, try using the metal spudger careful to not pop any keys out.

Step 7

Use hands to completely lift off the strip cover and remove.

Use hands to completely lift off the strip cover and remove.

Step 8

Use the Phillips #0 screwdriver again, unscrew all four Phillips PM 2.5X13.0mm screws from the top of the keyboard and set aside.

Use the Phillips #0 screwdriver again, unscrew all four Phillips PM 2.5X13.0mm screws from the top of the keyboard and set aside.

Step 9

Using your hands, lift the keyboard up from the top towards yourself until the keyboard is resting in your hand.
Do not aggressively pull at the keyboard for risk of ripping the connector cable.

Using your hands, lift the keyboard up from the top towards yourself until the keyboard is resting in your hand.

Do not aggressively pull at the keyboard for risk of ripping the connector cable.

Step 10

Gently slide out the connecting cable from the laptop to the keyboard.
Do not aggressively pull at the connecting cable.

Gently slide out the connecting cable from the laptop to the keyboard.

Do not aggressively pull at the connecting cable.

Step 11

Completely remove the keyboard from the rest of the laptop.

Completely remove the keyboard from the rest of the laptop.

Step 12

              Screen

Flip the Pavilion back over on its backside.

Flip the Pavilion back over on its backside.

Step 13

Using the same Phillips #0 screwdriver, unscrew the six Phillips PM 2.5X6.0mm screws.
Also remove the four Phillips PM 2.5X13.0mm screws to remove the thermal plate with the same screwdriver.

Using the same Phillips #0 screwdriver, unscrew the six Phillips PM 2.5X6.0mm screws.

Also remove the four Phillips PM 2.5X13.0mm screws to remove the thermal plate with the same screwdriver.

Step 14

Flip the laptop back over and open the lid all the way.
Using the flat edge of the plastic spudger, pry straight up to remove the Mini PCI Connector Cables from the board.
Tweezers can also be used to gently squeeze and pull up on the Mini PCI Cable Connectors to remove from the board.
When reinstalling, place the Mini PCI Connector Cables back in place and gently press straight down until they snap into place.

Flip the laptop back over and open the lid all the way.

Using the flat edge of the plastic spudger, pry straight up to remove the Mini PCI Connector Cables from the board.

Tweezers can also be used to gently squeeze and pull up on the Mini PCI Cable Connectors to remove from the board.

When reinstalling, place the Mini PCI Connector Cables back in place and gently press straight down until they snap into place.

Step 15

Using the tweezers, gently squeeze and pull backwards on the display cable until it is disconnected.
To reinsert, simply align the display cable to its proper spot and gently push into place.

Using the tweezers, gently squeeze and pull backwards on the display cable until it is disconnected.

To reinsert, simply align the display cable to its proper spot and gently push into place.

Step 16

Use the Phillips #0 screwdriver again to remove the four Phillips 2.5X13.0mm screws that hold the clips for the screen into place.

Use the Phillips #0 screwdriver again to remove the four Phillips 2.5X13.0mm screws that hold the clips for the screen into place.

Step 17

Turn the laptop around until the top cover is facing you. Keep the laptop in an open position.
Unscrew the four Phillips PM 2.5X6.0mm screws using the Phillips #0 that hold the clips of the screen on to the base.

Turn the laptop around until the top cover is facing you. Keep the laptop in an open position.

Unscrew the four Phillips PM 2.5X6.0mm screws using the Phillips #0 that hold the clips of the screen on to the base.

Step 18

Firmly grasp the top of the screen with your hands and pull towards you and upwards to remove the screen from the base.

Firmly grasp the top of the screen with your hands and pull towards you and upwards to remove the screen from the base.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Eliza Marks

Member since: 10/18/2016

649 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       UMass Dartmouth, Team 4-6, Catania Fall 2016                        

                                                  Member of UMass Dartmouth, Team 4-6, Catania Fall 2016 



                    UMASSD-CATANIA-F16S4G6                     


                                            3 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team