Difficulty

Moderate

Steps

11

Time Required

                          20 minutes

Sections

1

  • Screen
  • 11 steps

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackHP Pavilion ze5000

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Screen
  • Remove two 5.0 mm Philips #0 screws on the hinge of the device

Remove two 5.0 mm Philips #0 screws on the hinge of the device

1024

Step 2

  • Using tweezers, gently pull on the hinges to remove the plastic case connected to the hinges

Using tweezers, gently pull on the hinges to remove the plastic case connected to the hinges

Step 3

  • Remove the connection between the plastic case and interior of the device

Remove the connection between the plastic case and interior of the device

Step 4

  • Remove the connection from the exposed hinge and interior of the device

Remove the connection from the exposed hinge and interior of the device

Step 5

  • Remove the 3.5 mm philips #00 screw on the small circuit board on the hinge

Remove the 3.5 mm philips #00 screw on the small circuit board on the hinge

Step 6

  • Remove the 5.0 mm philips #0 screw that was hidden underneath the small circuit board

Remove the 5.0 mm philips #0 screw that was hidden underneath the small circuit board

Step 7

  • Remove the 6 plastic caps located in the four corners of the screen and the top of the screen
  • It may be easier to use tweezers for this part

Remove the 6 plastic caps located in the four corners of the screen and the top of the screen

It may be easier to use tweezers for this part

Step 8

  • Unscrew the six 5.0 mm Philips #0 screws underneath the caps

Unscrew the six 5.0 mm Philips #0 screws underneath the caps

Step 9

  • Using a spudger, pry the plastic casing off of the screen.

Using a spudger, pry the plastic casing off of the screen.

Step 10

  • Remove four 5.0 mm Philips #0 screws located in the corners of the screen
  • These screws locations will be close to the screws locations in step 2.
  • During reassembly, make sure you do not confuse the proper screw placements from this step and step 4.

Remove four 5.0 mm Philips #0 screws located in the corners of the screen

These screws locations will be close to the screws locations in step 2.

During reassembly, make sure you do not confuse the proper screw placements from this step and step 4.

Step 11

  • Remove the four 3.5 mm Philips #00 screws from the sides of the aluminum casing.
  • There will be two 3.5 mm Philips screws on each side

Remove the four 3.5 mm Philips #00 screws from the sides of the aluminum casing.

There will be two 3.5 mm Philips screws on each side

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Eric Beaudry

Member since: 03/06/2018

823 Reputation

                                      3 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       UMass Dartmouth, Team S2-G7, Bernier Spring 2018                        

                                                  Member of UMass Dartmouth, Team S2-G7, Bernier Spring 2018 



                    UMASSD-BERNIER-S18S2G7                     


                                            2 Members                     


                                            4 Guides authored