Hp Pavilion X360 M3 U101Dx Display Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes

Sections

Keyboard Panel
5 steps
Display
2 steps

Flags

BackHP Pavilion x360 m3-u101dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

The HP Pavilion x360 m3-u101dx display is what allows the user to see and interact with the laptop. This display works as a touch screen as well, allowing for hand gestures and direct interaction with what is on the screen. A broken or malfunctioning display might show unusual colors on screen, not register touchscreen input, have visible cracks on it, or spots where nothing appears on it. Often, the display will not show anything or flicker on and off.

When removing a display, be very careful as it is made of glass, especially if the display is shattered or cracked. The sharp edges of glass can cut, so proceed with caution and consider following these instructions when dealing with a cracked screen.

What you need

Step 1

              Keyboard Panel

Flip the laptop over so that the bottom of the laptop is facing up.

Flip the laptop over so that the bottom of the laptop is facing up.

1024

Step 2

Remove five 1.4mm Phillips #1 screws from the bottom of the laptop.

Remove five 1.4mm Phillips #1 screws from the bottom of the laptop.

Step 3

Remove the rubber grip using a plastic opening tool.
Remove five 1.7mm Phillips #1 screws.

Remove the rubber grip using a plastic opening tool.

Remove five 1.7mm Phillips #1 screws.

Step 4

Lift open the laptop screen and flip it around so that the keyboard is facing up.
Insert a plastic opening tool into one of the corners to create a gap between the bottom panel and the keyboard panel.
Guide the plastic opening tool around the perimeter of the panel to detach all the clips that are supporting it in place.
Do not pull the panel off by one corner as it can cause damage to the plastic.
Detach the keyboard panel from the frame.
There are two ribbon cables attached to the keyboard and trackpad so do not pull the keyboard panel away until you disconnect these ribbons in the next step.

Lift open the laptop screen and flip it around so that the keyboard is facing up.

Insert a plastic opening tool into one of the corners to create a gap between the bottom panel and the keyboard panel.

Guide the plastic opening tool around the perimeter of the panel to detach all the clips that are supporting it in place.

Do not pull the panel off by one corner as it can cause damage to the plastic.

Detach the keyboard panel from the frame.

There are two ribbon cables attached to the keyboard and trackpad so do not pull the keyboard panel away until you disconnect these ribbons in the next step.

Step 5

Remove the two ribbon cables connected to the inside of the laptop by using a finger to lift up on the latches.
Remove the keyboard panel from the rest of the laptop.

Remove the two ribbon cables connected to the inside of the laptop by using a finger to lift up on the latches.

Remove the keyboard panel from the rest of the laptop.

Step 6

              Display

Use the iFixit opening tool to flip the cable tab up, located at the top right corner of the motherboard.
Detach the display power cable from the motherboard.
Once the cable is loose, remove it from the cable case.

Use the iFixit opening tool to flip the cable tab up, located at the top right corner of the motherboard.

Detach the display power cable from the motherboard.

Once the cable is loose, remove it from the cable case.

Step 7

Use the suction handle and attach it to the bottom corner of the display.
Slide the iFixit opening tool around the display to loosen the clips attaching it to the case.
If you have difficulty removing the display, move the suction handle to the other corners.
When the display is removed from the case, pull the power cable from the bottom case through the hinge.

Use the suction handle and attach it to the bottom corner of the display.

Slide the iFixit opening tool around the display to loosen the clips attaching it to the case.

If you have difficulty removing the display, move the suction handle to the other corners.

When the display is removed from the case, pull the power cable from the bottom case through the hinge.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 1 other contributor

                    Javier Guillen

Member since: 01/22/2020

139 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       York University, Team S8-G1, Turner Winter 2020                        

                                                  Member of York University, Team S8-G1, Turner Winter 2020 



                    YORK-TURNER-W20S8G1                     


                                            5 Members                     


                                            7 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team