Hp Pavilion X360 Convertible 14 Dw1025Nr Trackpad Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          20 minutes

Sections

Battery
5 steps
Trackpad
10 steps

Flags

BackHP Pavilion x360 Convertible 14-dw1025nr
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

The tools used are the Phillips head screwdriver #0 and #1, the opening picks, tweezers, and the spudger.

This guide involves a number of moving parts, but the steps are easy to follow for someone inexperienced with computer repairs. Keep in mind, organizing the pieces removed allows for an easier reconstruction of the device.

What you need

Step 1

              Battery

Turn off the device and set it upside down. Orient the hinges away from you.
Wedge the opening pick under the grip. Lift the end of the grip.
Pull the grip off all the way. Repeat for the second grip.

Turn off the device and set it upside down. Orient the hinges away from you.

Wedge the opening pick under the grip. Lift the end of the grip.

Pull the grip off all the way. Repeat for the second grip.

1024

Step 2

Use a Phillips #0 screwdriver to remove the 3 mm screw from the center bottom.
Use a Phillips #1 screwdriver to remove the 6 mm screw from all four corners of the bottom cover.

Use a Phillips #0 screwdriver to remove the 3 mm screw from the center bottom.

Use a Phillips #1 screwdriver to remove the 6 mm screw from all four corners of the bottom cover.

Step 3

Use the opening pick to separate the back panel from the device.
Begin near the hinge and carefully follow the perimeter until you have taken the pick around all four sides.
The back panel will come loose once the pick has been around the whole edge of the device.
Lift the panel off.

Use the opening pick to separate the back panel from the device.

Begin near the hinge and carefully follow the perimeter until you have taken the pick around all four sides.

The back panel will come loose once the pick has been around the whole edge of the device.

Lift the panel off.

Step 4

Use a Phillips #1 screwdriver to remove all four of the 4 mm screws that secure each corner of the battery.

Use a Phillips #1 screwdriver to remove all four of the 4 mm screws that secure each corner of the battery.

Step 5

Use the opening tool near the connector to gently apply pressure and lift the battery away from the device.
Once loose, lift the battery from the connector side to separate it from the device.
The stabilizer for the battery (small black part held in by the top left screw) may come loose. Leave the part in its original position.

Use the opening tool near the connector to gently apply pressure and lift the battery away from the device.

Once loose, lift the battery from the connector side to separate it from the device.

The stabilizer for the battery (small black part held in by the top left screw) may come loose. Leave the part in its original position.

Step 6

              Trackpad

Step 7

Use PH0 to remove the 3mm screw from the center bottom.
Use PH1 to remove the 6mm screw from all four corners.

Use PH0 to remove the 3mm screw from the center bottom.

Use PH1 to remove the 6mm screw from all four corners.

Step 8

Step 9

Use PH1 to remove all four of the 4mm screws on each corner of the battery.

Use PH1 to remove all four of the 4mm screws on each corner of the battery.

Step 10

Step 11

To unplug the trackpad, remove both stickers with angled tweezers.
Lift the connector clasp with spudger.
Use angled tweezers to lightly grip the ribbon cable and pull it out to lift cable off of black cover

To unplug the trackpad, remove both stickers with angled tweezers.

Lift the connector clasp with spudger.

Use angled tweezers to lightly grip the ribbon cable and pull it out to lift cable off of black cover

Step 12

Using the angled tweezers, grip one corner of the black cover and lift.

Using the angled tweezers, grip one corner of the black cover and lift.

Step 13

Hold back the black cover with one hand.
Use the PH0 screwdriver to remove three black screws (2.5mm) located at the top of the trackpad.

Hold back the black cover with one hand.

Use the PH0 screwdriver to remove three black screws (2.5mm) located at the top of the trackpad.

Step 14

Using the PH1 screwdriver, remove four screws (3mm) at the bottom of the trackpad.
Lift the metal cover off.

Using the PH1 screwdriver, remove four screws (3mm) at the bottom of the trackpad.

Lift the metal cover off.

Step 15

Hold back the black cover.
Use the angled tweezers to grip the metal screw tab located in the middle of the trackpad.
Lift up and away to remove the trackpad part.

Hold back the black cover.

Use the angled tweezers to grip the metal screw tab located in the middle of the trackpad.

Lift up and away to remove the trackpad part.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Amber Norton

Member since: 09/14/2022

661 Reputation

                                      4 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Western Carolina University, Team 1-3, Virtue Fall 2022                        

                                                  Member of Western Carolina University, Team 1-3, Virtue Fall 2022 



                    WCU-VIRTUE-F22S1G3                     


                                            4 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team