Difficulty

Difficult

Steps

13

Time Required

                          30 minutes

Sections

2

  • Screen
  • 8 steps
  • Hinges
  • 5 steps

Flags

0

  • BackHP Pavilion x360 14m-cd0003dx

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

For further information to determine if the Hinges needs to be replaced, please refer to this troubleshooting guide.

What you need

Step 1

              Screen
  • Turn off the computer.
  • Disconnect the power cord and any external devices connected to the computer.
  • Make sure the device is completely turned off or else you may risk injury through electric shock.

Turn off the computer.

Disconnect the power cord and any external devices connected to the computer.

Make sure the device is completely turned off or else you may risk injury through electric shock.

1024

Step 2

  • Use a plastic opening tool to carefully separate the screen from the plastic frame.
  • Work along the top first, and then down the left and right sides.

Use a plastic opening tool to carefully separate the screen from the plastic frame.

Work along the top first, and then down the left and right sides.

Step 3

  • The screen can then be separated from the frame and laid flat on top of the keyboard.
  • Do not pull and try to remove yet, as the screen is still connected by several cables.

The screen can then be separated from the frame and laid flat on top of the keyboard.

Do not pull and try to remove yet, as the screen is still connected by several cables.

Step 4

  • The next few steps involve disconnecting the screen from the laptop in several places.
  • The first place is connected to the left side of the thin blue board at the top.
  • Peel back the clear adhesive and remove the pin header from the port on the blue board.

The next few steps involve disconnecting the screen from the laptop in several places.

The first place is connected to the left side of the thin blue board at the top.

Peel back the clear adhesive and remove the pin header from the port on the blue board.

Step 5

  • The next place is underneath the gray adhesive. Peel back this adhesive to expose the connection underneath.
  • Disconnect the gold pin header from its port.

The next place is underneath the gray adhesive. Peel back this adhesive to expose the connection underneath.

Disconnect the gold pin header from its port.

Step 6

  • Repeat Step 4 for the connection on the right side.
  • Peel the clear adhesive and remove connection.

Repeat Step 4 for the connection on the right side.

Peel the clear adhesive and remove connection.

Step 7

  • Peel the thin gray adhesive strips.
  • Pull out the thin black cable underneath these strips. It is the same black cable that was disconnected in the previous steps.

Peel the thin gray adhesive strips.

Pull out the thin black cable underneath these strips. It is the same black cable that was disconnected in the previous steps.

Step 8

  • After the cable has been disconnected, the screen can be removed.

After the cable has been disconnected, the screen can be removed.

Step 9

              Hinges
  • Remove the three Phillip Head screws (5 mm)that hold in the bracket on each side.

Remove the three Phillip Head screws (5 mm)that hold in the bracket on each side.

Step 10

  • Slide the frame down past the brackets on each side.

Slide the frame down past the brackets on each side.

Step 11

  • Lay the laptop flat on your working surface.
  • Flip it over to get access to the back panel.
  • Remove the back panel screws and take off the back cover.

Lay the laptop flat on your working surface.

Flip it over to get access to the back panel.

Remove the back panel screws and take off the back cover.

Step 12

  • Use a Phillips #00 screwdriver to remove the 5 mm screws from the hinges on each side inside the laptop.

Use a Phillips #00 screwdriver to remove the 5 mm screws from the hinges on each side inside the laptop.

Step 13

  • Remove the hinges from both sides of the laptop.

Remove the hinges from both sides of the laptop.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Elijah Jope

Member since: 03/22/2022

373 Reputation

                                      3 Guides authored                  



                       Badges:
                       3

Team

                       UMass Dartmouth, Team 7-4, Sinclaire Spring 2022                        

                                                  Member of UMass Dartmouth, Team 7-4, Sinclaire Spring 2022 



                    UMASSD-SINCLAIRE-S22S7G4                     


                                            6 Members                     


                                            6 Guides authored