Hp Pavilion X360 14M Ba114Dx Dc Power Jack Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          50 minutes

Sections

Battery
9 steps
Motherboard
8 steps
DC Power Jack
2 steps

Flags

BackHP Pavilion x360 14m-ba114dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Finally, a prerequisite to this guide is removal of the battery. If you notice once the laptop is open that the battery is swollen, remove it with caution. If swollen, do not charge the battery, keep the battery at a stable room temperature, and dispose of it properly at a recycling center. This page will help you deal with a swollen battery. Another important thing is to make sure that you unplug your device from any external power sources and completely power it off before beginning this replacement.

What you need

Step 1

              Battery

Using a #0 Phillips-head screwdriver, remove the three 5 mm screws along the bottom of the back cover.
Using a #0 Phillips-head screwdriver, remove the 6 mm screw at the top of the back cover.

Using a #0 Phillips-head screwdriver, remove the three 5 mm screws along the bottom of the back cover.

Using a #0 Phillips-head screwdriver, remove the 6 mm screw at the top of the back cover.

1024

Step 2

Using the flat end of the Spudger, pry up the two rubber feet on the top of the laptop’s back cover.
Using a #0 Phillips-head screwdriver, remove the 8 mm screw under each of the rubber feet.

Using the flat end of the Spudger, pry up the two rubber feet on the top of the laptop’s back cover.

Using a #0 Phillips-head screwdriver, remove the 8 mm screw under each of the rubber feet.

Step 3

Open the laptop, with the display fully extended to 360 degrees so that the screen is on the table.
In this orientation, sliding the laptop around may scratch the screen. A blanket or a mat placed under the screen will help to prevent scratching.
Using the thinner end of an iFixit Plastic Opening Tool, pry open the keyboard panel from the base of the laptop near the screen hinges.

Open the laptop, with the display fully extended to 360 degrees so that the screen is on the table.

In this orientation, sliding the laptop around may scratch the screen. A blanket or a mat placed under the screen will help to prevent scratching.

Using the thinner end of an iFixit Plastic Opening Tool, pry open the keyboard panel from the base of the laptop near the screen hinges.

Step 4

Using the iFixit Plastic Opening Tool and the iFixit Opening Picks, work your way around the rest of the keyboard and pry it out of the base.

Using the iFixit Plastic Opening Tool and the iFixit Opening Picks, work your way around the rest of the keyboard and pry it out of the base.

Step 5

Grasp the keyboard with both hands and gently lift it out of the base.
Do not lift the keyboard completely out of the base, as there are ZIF connectors that must be removed first.

Grasp the keyboard with both hands and gently lift it out of the base.

Do not lift the keyboard completely out of the base, as there are ZIF connectors that must be removed first.

Step 6

Using a plastic Spudger, remove the ZIF connectors that attach the motherboard to the touchpad and the keyboard. Use the flat end of the Spudger to pop up the cap on top of the connector. The connector will then slide out of place.
Repeat this step for all three connectors.

Using a plastic Spudger, remove the ZIF connectors that attach the motherboard to the touchpad and the keyboard. Use the flat end of the Spudger to pop up the cap on top of the connector. The connector will then slide out of place.

Repeat this step for all three connectors.

Step 7

Using the flat end of the plastic Spudger, remove the ZIF connector attaching the volume button and headphone jack to the motherboard.
This ZIF ribbon is glued to the middle of the battery. You do not need to separate this ribbon from the battery in order to remove the battery from the device. You only need to unclip it at both ends.

Using the flat end of the plastic Spudger, remove the ZIF connector attaching the volume button and headphone jack to the motherboard.

This ZIF ribbon is glued to the middle of the battery. You do not need to separate this ribbon from the battery in order to remove the battery from the device. You only need to unclip it at both ends.

Step 8

Using a #1 Phillips-head screwdriver, remove the seven 4 mm screws around the battery.
Gently move the ZIF connector out of the way to reach the screw marked in orange. Then use the #1 Phillips-head screwdriver to unscrew it.

Using a #1 Phillips-head screwdriver, remove the seven 4 mm screws around the battery.

Gently move the ZIF connector out of the way to reach the screw marked in orange. Then use the #1 Phillips-head screwdriver to unscrew it.

Step 9

Using the thin end of the iFixit Plastic Opening Tool, pry the battery out of its place inside the laptop’s base.
Next, use your fingers to pull the battery out of its position.

Using the thin end of the iFixit Plastic Opening Tool, pry the battery out of its place inside the laptop’s base.

Next, use your fingers to pull the battery out of its position.

Step 10

              Motherboard

Using the plastic Spudger, remove the ZIF connector connecting the power button board to the motherboard. Remove the connector by popping the cap up on top of the connector and sliding it out of its slot.
This ZIF ribbon is glued to the middle of the fan and will not come off.

Using the plastic Spudger, remove the ZIF connector connecting the power button board to the motherboard. Remove the connector by popping the cap up on top of the connector and sliding it out of its slot.

This ZIF ribbon is glued to the middle of the fan and will not come off.

Step 11

Using the iFixit Plastic Opening Tool or the plastic Spudger, disconnect the touch screen cable from the motherboard. Flip up the ZIF connector and move the wire away from the connection point.
Pull the wire out from its track next to the speaker.

Using the iFixit Plastic Opening Tool or the plastic Spudger, disconnect the touch screen cable from the motherboard. Flip up the ZIF connector and move the wire away from the connection point.

Pull the wire out from its track next to the speaker.

Step 12

Use the Blunt Tweezers to disconnect the Wireless Card Antenna Cables. Start with the cable labeled M2, which is connected to Port #2. To disconnect he cable, grab it on both sides with the tweezers and pull up.

Use the Blunt Tweezers to disconnect the Wireless Card Antenna Cables. Start with the cable labeled M2, which is connected to Port #2. To disconnect he cable, grab it on both sides with the tweezers and pull up.

Step 13

Use the Blunt Tweezers to disconnect the Antenna Cable labeled A1, which is connected to Port #1. To disconnect he cable, grab it on both sides with the tweezers and pull up.
Using the Blunt Tweezers, unwind the cables from the track to the right of the speaker. The cables are held in place by two black hooks.

Use the Blunt Tweezers to disconnect the Antenna Cable labeled A1, which is connected to Port #1. To disconnect he cable, grab it on both sides with the tweezers and pull up.

Using the Blunt Tweezers, unwind the cables from the track to the right of the speaker. The cables are held in place by two black hooks.

Step 14

Using the plastic Spudger, remove the ZIF connector that connects the motherboard to the Display Cable. To remove a ZIF connector, use the flat end of the Spudger to flip up the cap on the top. Then the connector should slide out.

Using the plastic Spudger, remove the ZIF connector that connects the motherboard to the Display Cable. To remove a ZIF connector, use the flat end of the Spudger to flip up the cap on the top. Then the connector should slide out.

Step 15

Using the curved end of the Halberd Spudger, disconnect the Speaker Cable from the port that connects it to the motherboard by prying it out of the port.
Using the same process to disconnect the DC Power Jack Cable from the port that connects it to the motherboard.

Using the curved end of the Halberd Spudger, disconnect the Speaker Cable from the port that connects it to the motherboard by prying it out of the port.

Using the same process to disconnect the DC Power Jack Cable from the port that connects it to the motherboard.

Step 16

Using a #1 Phillips-head Screwdriver, remove the ten 5 mm screws that secure the motherboard and fan to the base.
Using a #1 Phillips-head Screwdriver, remove the singular 2 mm screw that connects the motherboard to the wireless card.

Using a #1 Phillips-head Screwdriver, remove the ten 5 mm screws that secure the motherboard and fan to the base.

Using a #1 Phillips-head Screwdriver, remove the singular 2 mm screw that connects the motherboard to the wireless card.

Step 17

Using the plastic Spudger, gently lift up on the motherboard from the side that has the fan connected to it and remove the motherboard from the base.
Ensure that all connections to the motherboard have been disconnected. If they are not, the motherboard could be damaged upon removal.

Using the plastic Spudger, gently lift up on the motherboard from the side that has the fan connected to it and remove the motherboard from the base.

Ensure that all connections to the motherboard have been disconnected. If they are not, the motherboard could be damaged upon removal.

Step 18

              DC Power Jack

Using the Blunt Tweezers, gently lift the metal piece that covers the DC Power Jack unit and the metal piece will pop out.
Don’t forcefully pull on the metal piece because it could break.

Using the Blunt Tweezers, gently lift the metal piece that covers the DC Power Jack unit and the metal piece will pop out.

Don’t forcefully pull on the metal piece because it could break.

Step 19

Using the Blunt Tweezers, grab the DC Power Jack unit and gently lift it out.

Using the Blunt Tweezers, grab the DC Power Jack unit and gently lift it out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Jacob Morin

Member since: 01/24/2020

375 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Embry-Riddle Aeronautical University, Team S6-G4, Watkins Spring 2020                        

                                                  Member of Embry-Riddle Aeronautical University, Team S6-G4, Watkins Spring 2020 



                    ERAU-WATKINS-S20S6G4                     


                                            4 Members                     


                                            9 Guides authored

Moni1234 Moni - Jul 11, 2022

This is an amazing guide to repairing Hp Power Jack.

Check online HP DC Jack in India.

Introduction#

What you need#

Team#

Introduction

What you need

Team