Difficulty
Moderate
Steps
10
Time Required
30 minutes
Sections
3
- Battery
- 5 steps
- Motherboard
- 3 steps
- SSD
- 2 steps
Flags
0
BackHP Pavilion x360 14m-ba011dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the top left and right rubber pads closest to the hinge of screen using a plastic spudger to expose the screws underneath.
- Remove the following 6 screws from the bottom of the device using a Phillips #00 Screwdriver:
- Two 7.5 mm screws.
- Three 5 mm screws.
- One 6.5 mm screw.
Remove the top left and right rubber pads closest to the hinge of screen using a plastic spudger to expose the screws underneath.
Remove the following 6 screws from the bottom of the device using a Phillips #00 Screwdriver:
Two 7.5 mm screws.
Three 5 mm screws.
One 6.5 mm screw.
1024
Step 2
- Push into the two screw holes that were under the rubber pads with the screwdriver to pop the keyboard out just a little.
- Do this with the screen open so that you do not damage the screen.
- Do not remove keyboard all the way.
Push into the two screw holes that were under the rubber pads with the screwdriver to pop the keyboard out just a little.
Do this with the screen open so that you do not damage the screen.
Do not remove keyboard all the way.
Step 3
- Separate the keyboard from the rest of the device using a metal or plastic spudger around the edges.
- Pull up gently just until you can see the cables attaching the keyboard to the motherboard.
- Flip the small white flaps holding the cables to the motherboard open to unplug the cords.
Separate the keyboard from the rest of the device using a metal or plastic spudger around the edges.
Pull up gently just until you can see the cables attaching the keyboard to the motherboard.
Flip the small white flaps holding the cables to the motherboard open to unplug the cords.
Step 4
- Remove the purple cable attaching the battery to the motherboard by flipping the black flap and pulling the cable out.
- Remove seven 4 mm Philips screws using a Phillips #00 Screwdriver.
Remove the purple cable attaching the battery to the motherboard by flipping the black flap and pulling the cable out.
Remove seven 4 mm Philips screws using a Phillips #00 Screwdriver.
Step 5
- Remove the battery by gently pushing battery up, then pulling.
Remove the battery by gently pushing battery up, then pulling.
Step 6
Motherboard
- Unclip the 5 cables connecting the motherboard to the computer.
Unclip the 5 cables connecting the motherboard to the computer.
Step 7
- Remove ten 4 mm Phillips screws using a Phillips #00 Screwdriver.
Remove ten 4 mm Phillips screws using a Phillips #00 Screwdriver.
Step 8
- Gently remove the motherboard.
Gently remove the motherboard.
Step 9
SSD
- Flip the motherboard over to expose the SSD.
- Using a Phillips #00 screwdriver, remove one 3 mm silver screw that holds the SSD in place.
Flip the motherboard over to expose the SSD.
Using a Phillips #00 screwdriver, remove one 3 mm silver screw that holds the SSD in place.
Step 10
- Carefully lift and remove the SSD assembly by gently sliding it out of its slot.
Carefully lift and remove the SSD assembly by gently sliding it out of its slot.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Griffin O’Shields
Member since: 09/20/2021
157 Reputation
2 Guides authored
Badges:
5
+2 more badges
Team
The Citadel Military College of South Carolina, Team 2-16, Eggleston Fall 2021
Member of The Citadel Military College of South Carolina, Team 2-16, Eggleston Fall 2021
CMCSC-EGGLESTON-F21S2G16
2 Members
3 Guides authored
