Hp Pavilion X2 10 N113Dx Touch Pad Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 minutes

Sections

Touch Pad
9 steps

Flags

BackHP Pavilion x2 10-n113dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Touch Pad

Separate the screen from the keyboard.

Separate the screen from the keyboard.

1024

Step 2

Loosen the adhesive under the gray plastic bar using a heat pad or a heat gun.
Remove the gray plastic bar after 5 minutes of light heat with tweezers by pulling up.

Loosen the adhesive under the gray plastic bar using a heat pad or a heat gun.

Remove the gray plastic bar after 5 minutes of light heat with tweezers by pulling up.

Step 3

Remove the 4 screws with a Phillips #0 screwdriver.
These 4 screws have a diameter of 4.3 mm and a height of 3.7 mm.

Remove the 4 screws with a Phillips #0 screwdriver.

These 4 screws have a diameter of 4.3 mm and a height of 3.7 mm.

Step 4

Remove the rubber stoppers at the top left and right with tweezers.
Remove the screws at the top and right with at Phillips #0 screwdriver.
These two screws have a diameter of 5.3 mm and a height of 4.3 mm.

Remove the rubber stoppers at the top left and right with tweezers.

Remove the screws at the top and right with at Phillips #0 screwdriver.

These two screws have a diameter of 5.3 mm and a height of 4.3 mm.

Step 5

Pry open the back case with a metal spudger.
Then pry open the back layer with the metal spudger.

Pry open the back case with a metal spudger.

Then pry open the back layer with the metal spudger.

Step 6

Fully take off the back panel by lifting up the panel.

Fully take off the back panel by lifting up the panel.

Step 7

Pop open the ribbon cable piece on the touch pad with the blue plastic spudger.
Remove the ribbon cable with tweezers by pulling it out.

Pop open the ribbon cable piece on the touch pad with the blue plastic spudger.

Remove the ribbon cable with tweezers by pulling it out.

Step 8

Remove 4 screws with at Phillips #0 screwdriver. All 4 screws have a diameter of 4.3 mm and a height of 3.7 mm.
Lift the tape shown with orange boxes with tweezers.
Remove metal bar with a blue spudger.

Remove 4 screws with at Phillips #0 screwdriver. All 4 screws have a diameter of 4.3 mm and a height of 3.7 mm.

Lift the tape shown with orange boxes with tweezers.

Remove metal bar with a blue spudger.

Step 9

Lift up the touch pad by the metal edge with a blue plastic spudger.
Remove the touch pad from the computer.

Lift up the touch pad by the metal edge with a blue plastic spudger.

Remove the touch pad from the computer.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Cayla Skaggs

Member since: 04/01/2019

337 Reputation

                                      2 Guides authored                  



                       Badges:
                       3

Team

                       IUPUI, Team S1-G4, Harley Spring 2019                        

                                                  Member of IUPUI, Team S1-G4, Harley Spring 2019 



                    IUPUI-HARLEY-S19S1G4                     


                                            3 Members                     


                                            3 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team