Hp Pavilion X2 10 N113Dx Camera Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 minutes

Sections

Camera
9 steps

Flags

BackHP Pavilion x2 10-n113dx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Camera

Separate the screen from the keyboard.
The keyboard and screen are held together via magnets.
Open the device and pull the screen parallel to its face.

Separate the screen from the keyboard.

The keyboard and screen are held together via magnets.

Open the device and pull the screen parallel to its face.

1024

Step 2

Separate the screen from body of the computer with a blue spudger.
Using a plastic spudger, gently begin separating the face from the body.
Separate each side gently.

Separate the screen from body of the computer with a blue spudger.

Using a plastic spudger, gently begin separating the face from the body.

Separate each side gently.

Step 3

Once each edge has been separated, gently lift the face (screen) from the back.
Be sure to not do so quickly or you risk tearing the keyboard ribbon cable.
Rotate the device 180 degrees for the following steps.

Once each edge has been separated, gently lift the face (screen) from the back.

Be sure to not do so quickly or you risk tearing the keyboard ribbon cable.

Rotate the device 180 degrees for the following steps.

Step 4

Follow the attached ribbon cable to the circuit board of the device.
On the side of the ribbon cable, use a small plastic spudger to pop open this plastic lock and gently pull in the direction of the cable to remove.
Gently lift up on the battery connector just below the earlier removed ribbon cable to remove.

Follow the attached ribbon cable to the circuit board of the device.

On the side of the ribbon cable, use a small plastic spudger to pop open this plastic lock and gently pull in the direction of the cable to remove.

Gently lift up on the battery connector just below the earlier removed ribbon cable to remove.

Step 5

Unscrew and remove each of the four indicated screws using the Phillips #0 screwdriver.
Begin with the bottom left 4.5mm diameter screw.
Continue to the remaining three 2.0 mm diameter screws.
Once all four screws have been removed lift the battery from the device using the indicated pull tab along the top edge.

Unscrew and remove each of the four indicated screws using the Phillips #0 screwdriver.

Begin with the bottom left 4.5mm diameter screw.

Continue to the remaining three 2.0 mm diameter screws.

Once all four screws have been removed lift the battery from the device using the indicated pull tab along the top edge.

Step 6

Using a small blue plastic spudger pop off the two speaker wires from the circuit board.
Once removed from the board carefully move the wires from the raised clips on the metal plating.

Using a small blue plastic spudger pop off the two speaker wires from the circuit board.

Once removed from the board carefully move the wires from the raised clips on the metal plating.

Step 7

Using the Phillips #0 screwdriver, remove the 4.5mm screw from the camera circuit board.
Using a plastic spudger flip up the two rubber covers to the right and left of the 4.5mm screw.

Using the Phillips #0 screwdriver, remove the 4.5mm screw from the camera circuit board.

Using a plastic spudger flip up the two rubber covers to the right and left of the 4.5mm screw.

Step 8

Carefully remove the ribbon cable from the camera circuit board with tweezers.
Carefully remove the wire mesh tape from the metal plating using tweezers.

Carefully remove the ribbon cable from the camera circuit board with tweezers.

Carefully remove the wire mesh tape from the metal plating using tweezers.

Step 9

Using a plastic spudger remove the camera circuit board from the device.

Using a plastic spudger remove the camera circuit board from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Cayla Skaggs

Member since: 04/01/2019

337 Reputation

                                      2 Guides authored                  



                       Badges:
                       3

Team

                       IUPUI, Team S1-G4, Harley Spring 2019                        

                                                  Member of IUPUI, Team S1-G4, Harley Spring 2019 



                    IUPUI-HARLEY-S19S1G4                     


                                            3 Members                     


                                            3 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team