Difficulty
Moderate
Steps
13
Time Required
30 - 35 minutes
Sections
2
- Hard Drive
- 6 steps
- System Fan
- 7 steps
Flags
0
BackHP Pavilion Wave 600-a014
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Hard Drive
- Disconnect the PC from power source and any other devices.
Disconnect the PC from power source and any other devices.
1024
Step 2
- Turn the computer over and remove the rubber feet.
- Remove the three 8mm Philips screws with a Philips #0 Screwdriver.
- Use a pry tool and lift up on the lid.
Turn the computer over and remove the rubber feet.
Remove the three 8mm Philips screws with a Philips #0 Screwdriver.
Use a pry tool and lift up on the lid.
Step 3
- Remove the two cables circled in red for the front IO panel.
Remove the two cables circled in red for the front IO panel.
Step 4
- From back IO panel pry open the casing as indicated.
From back IO panel pry open the casing as indicated.
Step 5
- To remove the hard drive, remove the four 8mm Philips screws using a Philips #0 Screwdriver.
- Remove Power and SATA cables from on top of the drive.
To remove the hard drive, remove the four 8mm Philips screws using a Philips #0 Screwdriver.
Remove Power and SATA cables from on top of the drive.
Step 6
- After screws have been removed grab the Hard Drive and pull it out of the dock.
After screws have been removed grab the Hard Drive and pull it out of the dock.
Step 7
System Fan
- After removing your hard drive, remove the two 1.2mm Phillips #1 screws from the bottom of your case .
After removing your hard drive, remove the two 1.2mm Phillips #1 screws from the bottom of your case .
Step 8
- Remove the 8 mm Phillips #0 screw that is connected the top bezel and the top cover using the driver kit.
Remove the 8 mm Phillips #0 screw that is connected the top bezel and the top cover using the driver kit.
Step 9
- Using a flathead screwdriver, remove the 8 mm Phillips #1 screw that connects the body casing and the top bezel(the one at the bottom of memory card slot).
Using a flathead screwdriver, remove the 8 mm Phillips #1 screw that connects the body casing and the top bezel(the one at the bottom of memory card slot).
Step 10
- Remove the top bezel.
- You will have to take off a pair of wire connecting the bezel with the body to be able to completely detach it.
Remove the top bezel.
You will have to take off a pair of wire connecting the bezel with the body to be able to completely detach it.
Step 11
- Turn the device to the top side where you can see the top cover and the speaker.
- Using a flathead or Phillips #1 screwdriver, unscrew all the eight 8.0 mm screws that connect the top cover to the other components of the casing.
- Gently remove the top cover.
Turn the device to the top side where you can see the top cover and the speaker.
Using a flathead or Phillips #1 screwdriver, unscrew all the eight 8.0 mm screws that connect the top cover to the other components of the casing.
Gently remove the top cover.
Step 12
- After removing the top cover, locate the system fan on the left side of memory compartment.
- Remove three 1.2 cm Phillips #1 screws that connect the fan with the main body.
After removing the top cover, locate the system fan on the left side of memory compartment.
Remove three 1.2 cm Phillips #1 screws that connect the fan with the main body.
Step 13
- Simply slide up the fan after removing the screws.
Simply slide up the fan after removing the screws.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Kyaw Soe
Member since: 09/27/2017
321 Reputation
2 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team S8-G4, Banghart Fall 2017
Member of Cal Poly, Team S8-G4, Banghart Fall 2017
CPSU-BANGHART-F17S8G4
4 Members
5 Guides authored
