Difficulty
Moderate
Steps
11
Time Required
10 - 30 minutes
Sections
2
- Hard Drive
- 8 steps
- Microphone
- 3 steps
Flags
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Better Introduction
Improve this guide by completing or revising its introduction.
BackHP Pavilion Wave 600-a010
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Hard Drive
- Remove the three rubber footings by prying from the bottom cover using the plastic opening tool.
Remove the three rubber footings by prying from the bottom cover using the plastic opening tool.
1024
Step 2
- Remove the three 24 mm screws from the bottom cover using a Phillips #2 screwdriver.
Remove the three 24 mm screws from the bottom cover using a Phillips #2 screwdriver.
Step 3
- Remove the bottom cover by lifting it up from chassis.
Remove the bottom cover by lifting it up from chassis.
Step 4
- Remove the three wires connecting the outer cover and front I/O port to the internal components (front usb and auxiliary assembly).
Remove the three wires connecting the outer cover and front I/O port to the internal components (front usb and auxiliary assembly).
Step 5
- Remove the outer cover by gently pulling apart and pulling away from the chassis.
Remove the outer cover by gently pulling apart and pulling away from the chassis.
Step 6
- Remove rear I/O bezel using plastic opening tool to pry apart the four clips holding the I/O bezel to the chassis.
Remove rear I/O bezel using plastic opening tool to pry apart the four clips holding the I/O bezel to the chassis.
Step 7
- Remove all other remaining cables from unit using the plastic opening tool to carefully pry apart the connections.
Remove all other remaining cables from unit using the plastic opening tool to carefully pry apart the connections.
Step 8
- Remove the HDD by first using the Phillips #2 screwdriver to remove the four 23 mm screws holding together the assembly and then pulling the HDD out of the chassis.
Remove the HDD by first using the Phillips #2 screwdriver to remove the four 23 mm screws holding together the assembly and then pulling the HDD out of the chassis.
Step 9
Microphone
- Remove the three 24 mm screws that connect the top cover to the chasis inside the HDD compartment using theTorx #15 screwdriver (an extension and torque lever might be useful).
Remove the three 24 mm screws that connect the top cover to the chasis inside the HDD compartment using theTorx #15 screwdriver (an extension and torque lever might be useful).
Step 10
- Disconnect the microphone computer chip from the internal components by first peeling away the black adhesive holding the wires to the chassis and gently pulling the chip and wires from its connection.
Disconnect the microphone computer chip from the internal components by first peeling away the black adhesive holding the wires to the chassis and gently pulling the chip and wires from its connection.
Step 11
- Remove the top bezel from the unit using a Torx Head #15 screwdriver to remove three 24 mm screws and a Phillips Head #00 screwdriver to remove the single 24 mm screw around the outside edge of the chassis.
Remove the top bezel from the unit using a Torx Head #15 screwdriver to remove three 24 mm screws and a Phillips Head #00 screwdriver to remove the single 24 mm screw around the outside edge of the chassis.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
clayton stokes
Member since: 09/20/2017
652 Reputation
5 Guides authored
Badges:
8
+5 more badges
Team
Idaho State University, Team S4-G3, Watkins Fall 2017
Member of Idaho State University, Team S4-G3, Watkins Fall 2017
ISU-WATKINS-F17S4G3
4 Members
5 Guides authored
