Difficulty

Moderate

Steps

12

Time Required

                          10 minutes

Sections

1

  • Screen Rotator
  • 12 steps

Flags

0

  • BackHP Pavilion tx2500

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Screen Rotator
  • Completely turn off and unplug device. Lay the device bottom side up on a soft surface.

Completely turn off and unplug device. Lay the device bottom side up on a soft surface.

1024

Step 2

  • Squeeze the latches on the battery until you hear a click. Slide out the battery.

Squeeze the latches on the battery until you hear a click. Slide out the battery.

Step 3

  • Using the Phillips #0 screwdriver, remove the 4.5 mm screw from the WLAN model screen.
  • Once unscrewed, lift the right side of the WLAN module compartment cover and swing it to the left.

Using the Phillips #0 screwdriver, remove the 4.5 mm screw from the WLAN model screen.

Once unscrewed, lift the right side of the WLAN module compartment cover and swing it to the left.

Step 4

  • Using the plastic opening tool, disconnect the WLAN antenna cables from the WLAN module.

Using the plastic opening tool, disconnect the WLAN antenna cables from the WLAN module.

Step 5

  • Using the Phillips #0 screwdriver, unscrew the 4.5 mm screw from the middle section in the battery compartment.

Using the Phillips #0 screwdriver, unscrew the 4.5 mm screw from the middle section in the battery compartment.

Step 6

  • Use the plastic opening tool to disconnect the wires in the upper corners.

Use the plastic opening tool to disconnect the wires in the upper corners.

Step 7

  • Flip the laptop front side up and then use your fingers to lift up the keyboard.

Flip the laptop front side up and then use your fingers to lift up the keyboard.

Step 8

  • Lift up the black latch that connects the film strip to the base of the computer.
  • Use the plastic opening tool to disconnect the film strip from the base of the computer.

Lift up the black latch that connects the film strip to the base of the computer.

Use the plastic opening tool to disconnect the film strip from the base of the computer.

Step 9

  • Rotate the screen 90 degrees and remove the base under the screen.

Rotate the screen 90 degrees and remove the base under the screen.

Step 10

  • Rotate the screen back towards you.
  • Lift up the convertible hinge to unclip it from the base of the computer.

Rotate the screen back towards you.

Lift up the convertible hinge to unclip it from the base of the computer.

Step 11

  • Using the Phillips #0 screwdriver, remove both of the 5.0 mm screws on the base of the rotator.

Using the Phillips #0 screwdriver, remove both of the 5.0 mm screws on the base of the rotator.

Step 12

  • Gently lift up and remove the screen.

Gently lift up and remove the screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Sarah Naiser

Member since: 10/13/2015

324 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Sam Houston State, Team 1-4, Blackburne Fall 2015                        

                                                  Member of Sam Houston State, Team 1-4, Blackburne Fall 2015 



                    SHSU-BLACKBURNE-F15S1G4                     


                                            4 Members                     


                                            5 Guides authored