Difficulty

Moderate

Steps

16

Time Required

                          40 - 45 minutes

Sections

5

  • Battery
  • 4 steps
  • Keyboard
  • 4 steps
  • Case
  • 4 steps
  • Motherboard
  • 3 steps
  • Speaker
  • 1 step

Flags

0

  • BackHP Pavilion Sleekbook 15-b000

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Unplug laptop from adapter and all other devices.

Unplug laptop from adapter and all other devices.

1024

Step 2

  • Flip the laptop over with battery facing you.

Flip the laptop over with battery facing you.

Step 3

  • Slide the battery lock on the right side open.
  • Slide the Battery release latch on the left side.

Slide the battery lock on the right side open.

Slide the Battery release latch on the left side.

Step 4

  • Pull battery out.

Pull battery out.

Step 5

              Keyboard
  • Remove the two 6.5mm Phillips #1 keyboard screws from bottom of laptop.

Remove the two 6.5mm Phillips #1 keyboard screws from bottom of laptop.

Step 6

  • Push screwdriver through screw hole top pop the keyboard.
  • Make sure the screen is open.

Push screwdriver through screw hole top pop the keyboard.

Make sure the screen is open.

Step 7

  • Pry up the keyboard.
  • The keyboard is still attached by it’s ribbon.

Pry up the keyboard.

The keyboard is still attached by it’s ribbon.

Step 8

  • Remove keyboard wire by popping latch under blue plastic

Remove keyboard wire by popping latch under blue plastic

Step 9

              Case
  • Using the spudger to lift up on the white tabs
  • Pull horizontally on the blue ribbon to disconnect the cables

Using the spudger to lift up on the white tabs

Pull horizontally on the blue ribbon to disconnect the cables

Step 10

  • Remove the five 5.5mm Phillips #1 screws from the case

Remove the five 5.5mm Phillips #1 screws from the case

Step 11

  • Remove eight 6.5mm Phillips #1 screws from the back cover

Remove eight 6.5mm Phillips #1 screws from the back cover

Step 12

  • Starting at a top corner, use the pry tool to split the case.
  • Slowly work around the case, pulling up gently to release the clips.

Starting at a top corner, use the pry tool to split the case.

Slowly work around the case, pulling up gently to release the clips.

Step 13

              Motherboard
  • Disconnect motherboard cable from left side USB and jacks

Disconnect motherboard cable from left side USB and jacks

Step 14

  • Remove the six 5.5mm Phillips #1 motherboard screws
  • Remove the one 3.5mm Phillips #1 screw from the WiFi chip

Remove the six 5.5mm Phillips #1 motherboard screws

Remove the one 3.5mm Phillips #1 screw from the WiFi chip

Step 15

  • Remove motherboard.

Remove motherboard.

Step 16

              Speaker
  • Use a plastic opening tool to carefully remove the right speaker.
  • Repeat this step for the left speaker.

Use a plastic opening tool to carefully remove the right speaker.

Repeat this step for the left speaker.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Sam Barkley

Member since: 02/13/2018

983 Reputation

                                      8 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       USF Tampa, Team S11-G2, Cheng Spring 2018                        

                                                  Member of USF Tampa, Team S11-G2, Cheng Spring 2018 



                    USFT-CHENG-S18S11G2                     


                                            4 Members                     


                                            10 Guides authored