Difficulty
Moderate
Steps
17
Time Required
45 minutes
Sections
4
- Battery
- 4 steps
- Keyboard
- 4 steps
- Case
- 4 steps
- Screen
- 5 steps
Flags
0
BackHP Pavilion Sleekbook 15-b000
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Unplug laptop from adapter and all other devices.
Unplug laptop from adapter and all other devices.
1024
Step 2
- Flip the laptop over with battery facing you.
Flip the laptop over with battery facing you.
Step 3
- Slide the battery lock on the right side open.
- Slide the Battery release latch on the left side.
Slide the battery lock on the right side open.
Slide the Battery release latch on the left side.
Step 4
- Pull battery out.
Pull battery out.
Step 5
Keyboard
- Remove the two 6.5mm Phillips #1 keyboard screws from bottom of laptop.
Remove the two 6.5mm Phillips #1 keyboard screws from bottom of laptop.
Step 6
- Push screwdriver through screw hole top pop the keyboard.
- Make sure the screen is open.
Push screwdriver through screw hole top pop the keyboard.
Make sure the screen is open.
Step 7
- Pry up the keyboard.
- The keyboard is still attached by it’s ribbon.
Pry up the keyboard.
The keyboard is still attached by it’s ribbon.
Step 8
- Remove keyboard wire by popping latch under blue plastic
Remove keyboard wire by popping latch under blue plastic
Step 9
Case
- Using the spudger to lift up on the white tabs
- Pull horizontally on the blue ribbon to disconnect the cables
Using the spudger to lift up on the white tabs
Pull horizontally on the blue ribbon to disconnect the cables
Step 10
- Remove the five 5.5mm Phillips #1 screws from the case
Remove the five 5.5mm Phillips #1 screws from the case
Step 11
- Remove eight 6.5mm Phillips #1 screws from the back cover
Remove eight 6.5mm Phillips #1 screws from the back cover
Step 12
- Starting at a top corner, use the pry tool to split the case.
- Slowly work around the case, pulling up gently to release the clips.
Starting at a top corner, use the pry tool to split the case.
Slowly work around the case, pulling up gently to release the clips.
Step 13
Screen
- Remove the four 5.5mm Phillips #1 screws attaching the screen.
Remove the four 5.5mm Phillips #1 screws attaching the screen.
Step 14
- Remove the two 3.5mm Phillips #1 screws from the bottom of the screen.
Remove the two 3.5mm Phillips #1 screws from the bottom of the screen.
Step 15
- Remove the screen from it’s case.
- Screen is still connected to it’s case by a wire.
Remove the screen from it’s case.
Screen is still connected to it’s case by a wire.
Step 16
- Lay the screen face down on a surface where it ill not scratch
Lay the screen face down on a surface where it ill not scratch
Step 17
- Lift up plastic over latch for the screen.
- Pull the connector away from the screen to disconnect it.
Lift up plastic over latch for the screen.
Pull the connector away from the screen to disconnect it.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Sam Barkley
Member since: 02/13/2018
983 Reputation
8 Guides authored
Badges:
8
+5 more badges
Team
USF Tampa, Team S11-G2, Cheng Spring 2018
Member of USF Tampa, Team S11-G2, Cheng Spring 2018
USFT-CHENG-S18S11G2
4 Members
10 Guides authored
